We have discovered this article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and think it made perfect sense to share it with you in this article.
Mounting a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can relocate quickly; if you need to open a wall to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to move out the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the task and also fit attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly help you install a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous water system pipelines.
Your devices and also product list must consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Using the two wood boards under its feet, position the bathtub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last position.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a stiff seal, triggering the water to permeate the wall in between the bath as well as the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very enthusiastic about Installing A Bathtub and I'm hoping you enjoyed our blog post. I beg you take a moment to promote this content if you enjoyed reading it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Book Your Installation